Variable Frequency Drives for individual adjustability on all air fans. Adds an infinite degree of fine-tuning to any separation process with super accurate digital readouts. Housed in a dust-tight, wash-down NEMA 12 enclosure, programmed at the factory for out-of-the-box use.
Standard on all Maxi-Cap Gravity Separators and Destoners, now available on all Hi-Cap machines. Monitors and adjusts deck motor speed for optimal separation performance fine-tuning and reduced power consumption. Eliminates the mechanical spring pulley assembly. All electronics housed in a dust-tight, wash-down NEMA 12 enclosure Programmed at the factory for out-of-the-box use.
Allows all Oliver equipment to be set precisely and accurately with less operator effort. Airflow gauges help adjust each fan speed, for more continuous and even product flotation. Electronic Tachometer is provides digital readout of eccentric (shake) speed. Angle Indicator scales show both deck side tilt and end raise adjustments.Very useful tools in setup or when switching between products. Standard on Hi-Caps and Maxi-Cap Gravity Separators and Destoners. Hole saw included for air gauge installation.
Rapidly conveys good product to the discharge hopper, improving capacity and eliminating wear and strain. Significantly extends operating life and promotes smooth, trouble-free operation. 1HP motor included.
On-off pneumatic actuator where the open position can be infinitely adjusted for uniform feed rate. Uses a manual screw adjustment for flow control and pressurized air line for positive shut-off. Remote control prevents material piling on the deck at machine shutdown. Available on all Oliver machines.
Continuously adjustable feed aperture for a nearly infinite and completely repeatable amount of feed control. Also completely shuts off feed at machine shutdown to prevent unwanted material piling. Controlled by touch screen panel on a Voyager or Maxi-Cap Platinum Gravity Separator. Available on Maxi Cap Platinum and Voyager Gravity Separators.
An assembly of counter-rotating mass synchronized to significantly reduce vibration transmitted by gravity separators or destoners. Will increase the operational life of high-wear machine parts such as bearings, shafts, etc. Recommended for machines installed on or above-grade floors or other locations without adequate foundation to reduce apparent vibration. May require additional equipment if installed with Air Chest Divider option. Standard on all Maxi-Cap Gravity Separators and Destoners, Voyagers and Hi-Cap Master Series machines.
Three economical means of removing light contaminants before and after the particles are delivered onto the separation deck. Greatly reduces the threat of environmental, processing and maintenance problems inherent in product flows that contain dust, chaff and other contaminants.
Aspirating Feeders convey product dust and chaff to an in-plant dust control system or an Oliver two-bag filter system. Can be ordered with fans, drives and bag filter system, and are capable of handling most mild dust problems.
Enclose the entire separation deck, and remove all airborne dust from product flow. Available as partial and complete dust hoods. Both include built-in exhaust air adjustment controls for precise balance of the incoming and exhaust air volume. Both must be connected to an in-house dust control system. Includes internal illumination for visual inspection.
Cleaner, more compact, non-protruding filters. Heavier, better built units with stainless steel screen replacing brass. Fit older machines with very minor attachment modification. Install into rather than on top of existing cutout, to reduce damage that can cut airflow and compromise performance, leak impurities or create dead airflow spots. Bolt hold downs replace hand screws to meet safety guidelines to cover motors and belt drives. Standard on all new Oliver machines, retrofittable on all older ones.
Heavy contaminants side discharge gate allows precise metering of heavy discharge and easy periodic flush (discharge) of heavy material accumulating in rock traps or on the high side. Spring-loaded design with redundant adjustable wheel. Infinitely adjustable for particle size. Available for all Hi-Cap Destoners and Gravity Separators.
For Precision Size Right only
Rigidized one-piece cylinder access doors with improved handles for positive door removal and better seating against frame. Available hinges allow swing down without removal. Viewing windows available.
For Precision Size Right only
Allen-BradleyTM safety system with coded magnet sensors to shut the machine down when they detect the door being opened. Can be fitted to cylinder doors and the door enclosing drive system belts Retrofittable to all older Size Right machines with electrical control cabinet.
For Precision Size Right only
Allen-BradleyTM safety system with coded magnet sensors to shut the machine down when they detect the door being opened. Can be fitted to cylinder doors and the door enclosing drive system belts Retrofittable to all older Size Right machines with electrical control cabinet.
For Precision Size Right only
Patented hard plastic roller system to positively dislodge particles inside the screen and keep them in motion. Available for manual operation or as an automated pneumatic control system. Retrofittable to all older Size Right equipment and Carter Day machines.
